I Can Find The Time

I have one more great project to show you for using up some of your wine corks.

Although if you are like me and you've already made more than one Wine Cork Board and/or Wine Cork Trivet you are running low on wine corks! That just means it's time to open another bottle...I love it! :)

This project is much more a piece of art than a practical and useful cork board, but still a very nice effect. It's a Monogrammed Wine Cork wall hanging.

Supplies you'll need:

- wine corks (a variety of sizes and colors)

-hot glue gun

-frame

-foam board (if your frame doesn't have a back)

-knife

The first step will be to glue the back onto the frame. My frames were the $2 ones from Ikea, so the didn't come with usable backs. I substituted some foam board that I cut to the right size and painted black. Using your hot glue gun make sure to get a good seal all the way around the frame.

Then you will start laying out the letter for the monogram. You'll need to cut about 7 corks into discs if you're using an 8x10 frame. I usually get 4 discs per cork. And depending on how you lay out your letter you may need more or fewer discs. But make sure to have fun with this part, and add a lot of visual interest to the wall hanging, by using corks with logos on the ends, or that were stained by red wine. I also used a champagne cork with a star on it for the top of the "C" for another special touch.

Once you have the letter laid out, you'll need to fill in all the surrounding area with corks that have been cut in half length wise. I always try to keep the logos whole when I cut corks in half, so my wall hanging will be very busy and graphic. Unless you are squaring off the letter in your wall hanging, you will end up with a ton of usual angles that need to be filled by very rectangular corks. It's not hard to get the entire background covered...just filled in as many whole corks as you can fit first (using the best designs, or course), and then started cutting them to fit. I ended up with one row on top of the "C" that is only 1/4 of a cork, but as long as the black is mostly covered you'll get the right effect.

Once you have your frame filled in the way you like simply glue each cork down one by one. You might have to make some adjustments as you glue, so keep all your left over cork pieces handy to fill in any large gaps.

I made a second wall hanging for my brother-in-law and used a slightly larger frame. The process was the same, but I liked how I added a row of 3 cork discs to each end of the "K" in this version. I think it makes the letter look capitalized and more like a traditional monogram. I'll definitely use that technique again when I make more of these.

Of course these wall hangings could be used as cork boards, but I think they are too nice to cover up. I added picture hangers to the back of each one so they could go up anywhere the recipient has a photo grouping.

I hope you like this idea for a way to repurpose used wine corks into a custom wall hanging...and that you can find the time to make one!

How many of you have a bowl or jar of wine corks sitting around? Well, we have had a collection going for about 5 years and I am finally doing something with them. I have quite a few projects in the works now to repurpose my wine corks, and the first I'm going to share is two different ways to make wine cork cork boards.

Here are the supplies you'll need for either cork board:

- lots of wine corks

-unfinished wood frame (with back)

-paint or stain for the frame

-hot glue gun

-kitchen knife

The first cork board is my favorite becasue I haven't really seen anything like it out there. I started by spray painting the frame black, followed by clear coat.

While that was drying I started on the corks. I knew I wanted to use the corks laid out on their ends instead of sides, so I started cutting them into 1/4" discs. I tried a few different knives/tools to cut the corks and found that a non-serrated edge kitchen knife works the best. Be careful, because some of the corks are harder to cut and they could slip out of your fingers. I also like that using the corks in these discs allows me to use the champagne corks in my projects. Those are all the slightly larger discs you see in the board.

Once I had a large pile of corks I started laying the out in a random pattern on my frame. I mixed the real corks in with the plastic ones; and mixed in some larger champagne cork discs as well. You'll have to work with fitting them in to get as many as you can in the space. I also cut some of the discs in half to fill in the larger gaps.

Once I had the layout I liked I used hot glue to attach them one by one. Be careful not to use too much glue or it will squeeze out around the cork and look sloppy.

And there you have it...a "Disc" wine cork cork board.

The second board I made is a more popular use of wine corks...and a little easier since you don't have to cut the corks.

I started with another unfinished wood frame, painted black.

I had a harder time arranging the corks for this board, and you will find that using the same length corks for each row will help you avoid large gaps. I wanted the corks to fit as closely as possible so I fiddled with the layout a lot longer than necessary.

Once I finally found a look that I like, I again used hot glue to attach the corks to the frame. You don't have to worry as much on this project about using too much glue, since the curve of the cork is better at hiding the glue than the flat discs.